OWNER’S MANUAL
LED LCD MONITOR
Please read this manual carefully before operating
your set and retain it for future reference.
LED LCD MONITOR MODELS
E1951S E1951T E2251VR E2251VQ
E2051S E2051T E2351VR E2351VQ
E2251S E2251T
E2351T
ASSEMBLING AND PREPARING
3
AsseMBLInG AnD PRePARInG
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
DVI-D Cable
CD(owner's Manual) /
D-sUB Cable
(E1951T/E2051T/E2251T/E2351T/
E2251VR/E2351VR/E2251VQ/
E2351VQ)
Card
(This signal cable may be attached
to this product before shipping out.)
(This cable is not included in all
countries.)
Power Cord
AC-DC Adapter
stand Base
stand Body
two screws
CAUtIon
Do not use any unapproved accessories to ensure the safety and product life span.
Any damages or injuries by using unapproved accessories are not covered by the warranty.
y
y
note
The accessories supplied with your product may vary depending on the model.
Product specifications or contents in this manual may be changed without prior notice due to upgrade
of product functions.
y
y
User should use shielded signal interface cables (RGB cable) with ferrite cores (core in the
connector) to maintain standard compliance for the product.
y
ASSEMBLING AND PREPARING
4
Parts and buttons
Power Indicator
Lighting on: turned on
Lighting off: turned off
y
y
(Power Button)
Button ("CUSTOMIZING
E2251VR E2251VQ
E2351VR E2351VQ
E1951S E2051S E2251S
E1951T E2051T
E2251T E2351T
ASSEMBLING AND PREPARING
5
Button
Description
MENU
Left First Button
osD LoCKeD/
UnLoCKeD
This function allows you to lock the current control settings, so
that they cannot be inadvertently changed.
Press and hold the Left First Button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing the
Left First Button for several seconds. The message "OSD
UNLOCKED" should appear.
SUPER+ RESOLUTION
DUAL
Use this button to enter the DUAL menu.
AUTO
To automatically adjust the screen, press the AUTO button on the MONITOR SETUP
OSD. (Only supported in Analog Mode)
the best display mode
e1951s / e1951t
e2051s / e2051t
1366 x 768
1600 x 900
1920 x 1080
e2251s / e2251t
e2251VR / e2251VQ
e2351t / e2351VR
e2351VQ
VOLUME (Only HDMI mode) e2251VR / e2351VR / e2251VQ / e2351VQ
INPUT
You can choose the input signal.
When two input signals are at least are connected, you can select the input signal
y
(D-SUB/HDMI) you want.
When only one signal is connected, it is automatically detected. The default setting is
D-SUB.
y
EXIT
Exit the OSD(On Screen Display).
Turns the power on or off.
(Power Button)
Power Indicator
The power indicator stays white if the display is running
properly (On Mode). If the display is in Sleep Mode, the power
indicator color is red.
ASSEMBLING AND PREPARING
6
Using a coin, turn the screw clockwise to se-
cure the stand base.
4
setting Up the Monitor set
Attaching the stand Base
Place the monitor's screen face down.
1
CAUtIon
To protect the screen from scratches, cover
the surface with a soft cloth.
y
Put the stand Body on the set and use the
screws to fix.
2
stand Base
Detaching the stand base
Place the monitor's screen face down.
To protect the screen from scratches, cover the
surface with a soft cloth.
1
Using a coin, turn the screw in the stand base
counterclockwise. Detach the stand base from
the stand body.
2
stand Body
Check the position (at the front and rear) of
the stand body, then mount the stand base on
the stand body as shown in the figure.
3
stand Body
stand Body
stand Base
CAUtIon
stand Base
This illustration depicts the general type of
connection. Your monitor may differ from the
items shown in the picture.
Do not carry the product upside down
holding only the stand base. The product
may fall and get damaged or injure your
foot.
y
CAUtIon
y
Push stand base tightly before turn the
screw in.
y
ASSEMBLING AND PREPARING
7
Connect the AC-DC Adapter and Power Cord
to a wall outlet.
2
Detaching the stand Body (Using
the Wall mount)
Remove 2 screws and detach the Stand Body.
1
Press Power button on the front switch of panel
to turn the power on.
3
CAUtIon
Mounting on a table
Disconnect the power cord first, and then move
or install the Monitor set. Otherwise electric
shock may occur.
Lift and tilt the Monitor set into its upright
position on a table.
1
Leave a 10 cm (minimum) space from the wall
for proper ventilation.
10 cm
10 cm
10 cm
10 cm
ASSEMBLING AND PREPARING
8
manual supplied with the Kensington security
WARnInG
When you adjust the angle, do not hold the
bottom of the Monitor set frame as shown on
the following illustration, as it may injure your
fingers.
Connect the Kensington security system cable
between the Monitor set and a table.
Do not touch or press the screen when
adjusting the angle of the monitor.
note
The Kensington security system is optional.
You can obtain it from most electronics stores.
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
note
Tilt from +15 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.
- 5
15
10 cm
10 cm
10 cm
10 cm
Front
Rear
Using the Kensington security system
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
ASSEMBLING AND PREPARING
9
If you intend to mount the Monitor set to a wall, an
optional third-party wall mount must be purchased.
When you install the Monitor set using the wall
mounting interface (optional parts), attach it
carefully so it will not fall.
VESA (A x B)
y
A
B
Please use screws and a wall mount interface
in accordance with VESA Standards.
If you use screws longer than standard, the
monitor might be damaged internally.
1
2
If you use improper screws, the product might be
damaged and drop from mounted position. In
this case, LG Electronics is not responsible for it.
3
4
5
CAUtIon
VESA compatible only with respect to screw
mounting interface dimensions and mounting
screw specifications.
Disconnect the power cord first before
moving or installing the Monitor set.
Otherwise electric shock may occur.
If you install the Monitor set on a ceiling or
slanted wall, it may fall and result in severe
injury.
Use only an authorized LG wall mount and
contact a local dealer or qualified personnel.
Do not over tighten the screws as this may
cause damage to the Monitor set and void
your warranty.
y
y
Please use a VESA standard as below.
784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm
y
Φ
* Screw : 4.0 mm x Pitch 0.7 mm x
y
y
Length 10 mm
787.4 mm (31.0 inch) and above
* Please use VESA standard wall mount pad
and screws.
y
Use only screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
y
Model
E1951S
E2051S E2251VR
E2251S E2351VR
E2351T
E2251VQ
E2351VQ
E1951T
E2051T
E2251T
note
VesA (A x B)
screw size
number of screws
Wall mount bracket
(optional)
75 x 75
M4
4
Only use screws that are listed on the VESA
standard screw specifications.
The wall mount kit will include an installation
manual and necessary parts.
The wall mount bracket is optional. You can
obtain additional accessories from your local
dealer.
y
RW120
y
y
The length of screws may differ depending
on the wall mount. Be sure to use the proper
length.
For more information, refer to the
instructions supplied with the wall mount.
y
y
USING THE MONITOR SET
10
UsInG tHe MonItoR set
Connecting to a PC
E2251VR E2351VR E2251VQ E2351VQ
Your Monitor set supports Plug & Play*.
*Plug & Play: A PC recognizes a connected
device that users connect to a PC and turn
on, without device configuration or user
intervention.
y
D-sUB connection
Transmits analog video from your PC to the
Monitor set. Connect the PC and the Monitor set
with the supplied D-sub 15 pin signal cable as
shown in the following illustrations.
E1951S E2051S E2251S
note
Apple Adapter
y
An adapter may be needed for Apple
computers. This adapter can be purchased
from Apple.
E1951T E2051T E2251T E2351T
|