Manitowoc Ice Ice Maker K00049 User Manual

K00049 STACKING KIT  
Installation Instructions  
These instructions are for stacking an E-0400, G-0400, or G-0600 ice machine on a G-1200 ice machine. The bin must be  
level before proceeding.  
PARTS LIST:  
Item Description  
Qty.  
1
1
1
1
1
1
1
1
P/N  
1.  
2.  
Ice Chute Weldment  
Top Cover  
6639714  
6870914  
6639814  
6639914  
6640014  
6025014  
6091314  
6207014  
6273014  
8003293  
8106243  
3.  
Water Shield  
4.  
5.  
6.  
Top Mounting Bracket  
Bottom Mounting Bracket  
Bin Thermostat  
7.  
8.  
9.  
Bin Thermostat Bulb Mounting Bracket  
Electrical Box Front Cover  
Tie Plate  
1
1
1
10.  
11.  
12.  
13.  
14.  
15.  
16.  
17.  
Installation Instructions  
Label - Wiring Diagram  
RTV Sealer (3 oz. tube)  
Foam Tape  
Screw #10-24 x 5/8" P.P.H.T.C.  
Screw #10-24 x 3/8" Slotted Hex Hd. TCS  
Screw #8 x 1/2" S.M.S.  
Wing Nut #8-32  
1
9100691  
114"  
9202483  
5202053  
5202103  
5121531  
5489021  
5
3
1
4
1. INSTALLATION OF BIN THERMOSTAT BRACKET:  
A. Locate the bin, as shown in Illustration 1.  
2. INSTALLATION OF G-1200 ICE MACHINE:  
A. See service manual for uncrating and inspection of ice machine.  
B. Remove top cover from ice machine.  
C. Set ice machine carefully and squarely on bin.  
D. Position top cover from kit on right-hand side of ice machine. Attach water shield from kit to top cover using one #8 x  
1/2" long sheet metal screw from kit (see Illustration 2).  
E. Apply foam tape from kit, as shown in Illustration 2  
3. INSTALLATION OF E-0400, G-0400, OR G-0600 ICE MACHINE:  
NOTE: G-0600 IS USED TO REPRESENT ANY E-0400, G-0400, OR G-0600.  
A. See service manual for uncrating and inspection of ice machine.  
B. Remove top cover from ice machine.  
C. Position G-0600 ice machine on G-1200 ice machine with back and left sides being flush.  
Attach machines together using the tie plate from kit on left side of machines. Remove the right side panel from the  
G-0600 ice machine. Drill a 5/32" diameter hole in top cover using an existing hole in the bottom angle of the G-0600  
ice machine as a guide. NOTE: Be sure not to damage internal parts of the G-1200 ice machine (see Illustration 3).  
D. Before applying RTV sealant in designated areas to insure against leaks or water hang-ups (as shown in Illustration 4),  
remove the water pump, high and low valve plastic cover, water curtain, and water trough. After sealing seams with  
RTV, replace water pump, water curtain, high and low valve plastic cover, and water trough.  
Manitowoc Ice, Inc.  
2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA  
Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879  
8003293  
Sheet 1 of 10  
Rev. 05/17/01  
4. INSTALLATION OF BIN THERMOSTAT BULB:  
 
Sheet 3 of 10  
Rev. 05/17/01  
8003293  
Sheet 4 of 10  
Rev. 05/17/01  
8003293  
Sheet 5 of 10  
Rev. 05/17/01  
8003293  
Sheet 6 of 10  
Rev. 05/17/01  
8003293  
Sheet 7 of 10  
Rev. 05/17/01  
8003293  
Sheet 8 of 10  
Rev. 05/17/01  
8003293  
Sheet 9 of 10  
Rev. 05/17/01  
8003293  
Sheet 10 of 10  
Rev. 05/17/01  
 

Lasko Fan Model 4000 User Manual
Legacy Car Audio Car Video System LD63MU User Manual
LG Electronics Air Conditioner LCN240CP User Manual
LG Electronics Cell Phone Accessories MFL67235901 User Manual
Lincoln Electric Welder SVM107 B User Manual
Magnavox Flat Panel Television 26MF321B User Manual
Makita Sander 9401 User Manual
Mark Levinson Stereo Amplifier N433 User Manual
Mercedes Benz Automobile 2002 E 320 User Manual
Metrologic Instruments Scanner MS9520 Voyager User Manual