Liebherr Refrigerator 7082 135 00 User Manual

Operating instructions  
Page 12  
GB  
Combined refrigerator-freezer  
7082 135-00  
ECN 61 111  
 
GB  
Description of appliance and equipment  
1
2
3
4
5
6
7
8
9
bl  
bm  
bn  
Operating and control elements  
Adjustable door racks  
Adjustable storage shelves  
Bottle rack  
Type plate (behind the vegetable drawer on the left-hand side)  
Drawer  
Vegetable drawers  
Water filter  
Upper freezer drawer  
Lower freezer drawer  
IceMaker (in the interior of the upper freezer drawer)  
Ventilation grille. In this area, the exchange of air for the refrig-  
eration unit takes place. Never cover this grille or otherwise  
obstruct the air flow.  
Temperature and control display  
Water filter has to be changed  
Refrigerator temperature display  
Operating and control elements  
Menu mode is activated  
The electronic control panel has the new "touch capacitance  
technology". Any function can be activated by touching the cor-  
responding icon.  
(for setting additional functions)  
Freezer temperature display  
The exact contact point  
is between the symbol and its label  
Refrigerator  
operating icons  
Control  
icons  
Freezer  
operating icons  
Freezer operating icons  
Refrigerator operating icons  
Control icons  
Temperature setting icons  
Mute alarm (refrigerator and freezer)  
Power failure LED  
Freezer ON/OFF  
SuperFrost  
SuperCool  
Dust filter LED  
The dust filter in the appliance  
plinth must be cleaned.  
Refrigerator ON/OFF  
Temperature setting buttons  
IceMaker ON/OFF  
SuperCool LED  
Child lock LED  
Alarm LED  
IceMaker ON LED  
SuperFrost LED  
13  
 
Water filter  
Installing the water filter  
Before switching on the appliance, install the water filter provided  
in the interior rear wall of the refrigerator compartment.  
This ensures good ice cube quality and keeps the water circuit  
free of solids such as sand.  
1. Remove the cover of the filter  
socket.  
Water filter  
location  
2. Insert the filter and turn it 90°  
clockwise.  
Replace the filter when the waterdrop  
symbol appears in the temperature  
display.  
Filters can be obtained from your dealer.  
Thedropsymbolmustbecancelledafter  
the filter has been changed. For detailed  
instructions see section entitled "Setup  
mode".  
Removing the water filter  
Caution!  
3. Turn the filter 90° anticlockwise  
and remove.  
To avoid the risk of bacteria growth, the water filter  
must be changed when the waterdrop symbol appears  
on the display!  
It is not necessary to switch off the water supply when removing  
or installing the water filter.  
Saving energy  
- Always ensure good ventilation. Do not cover ventilation open-  
ings or grille.  
- Always keep fan louvres clear.  
- Do not place appliance in areas of direct sunlight or next to a  
stove, heater or similar object.  
- Theenergyconsumptiondependsontheinstallationconditions,  
e.g. the ambient temperature.  
- Keep the time the appliance is open to a minimum.  
- Store food logically.  
- Ensure that all food is well packed and covered for storage. This  
will prevent frost from forming.  
- First cool warm food to room temperature before storing it.  
- Defrost frozen food in the refrigerator.  
- If there is a thick layer of frost in the appliance: defrost the appli-  
ance.  
- Emptyandswitchoffrefrigeratingunitforlongervacationperiods.  
- Use the vacation function for longer vacation periods.  
Accumulated dust increases the energy consumption:  
- Once a year, dust the refrigerating unit together with the metal  
grille of the heat exchanger at the back of the appliance.  
14  
 
GB  
Audible warning signal  
Switching the appliance on and off  
The appliance is equipped with an alarm function.  
You are advised to clean the appliance before switching it on for  
the first time (see "Cleaning").  
Audible door alarm:  
Do not load with frozen food until the temperature shows at least  
-18°C. The refrigerator and freezer compartments can be oper-  
ated separately.  
If an appliance door is left open for more than 180 seconds,  
the audible warning signal will sound. Touch the ALARM  
icontocancelthealarm.Thealarmswitchesbacktostandby  
when the door is shut.  
Audible/visual temperature alarm:  
Switching on: Touch the On/Off icons (on left  
for refrigerator, on right for freezer) so that the  
temperature displays light up or flash.  
It sounds when it is not cold enough in the freezer compartment.  
The temperature display and the  
LED will also flash.  
The audible warning device is switched off by touching the  
ALARMicon.Thetemperaturedisplaywillcontinuetoflash  
until the cause of the alarm has been rectified.  
Switching off: Keep the On/Off icons pressed for approx. 3  
seconds.  
This can be caused by:  
• the freezer door being left open for a long time, allowing warm  
ambient air to enter;  
Setting the temperature  
The appliance is pre-set for normal operation. We recommend  
temperatures of +5°C in the refrigerator and -18°C in the freezer.  
• a long power failure;  
• a fault in the appliance.  
In each case, make sure food has not thawed or perished.  
To reduce the temperature: Touch the  
Down icon; on left for refrigerator and on  
right for freezer.  
To increase the temperature: Touch the  
Up icon.  
Power failure/FrostControl display  
If the  
LED lights up on the control panel, this means that the  
- While you are entering the temperature, the set temperature will  
flash on the display.  
freezer temperature has risen too high during the last few hours  
or days due to a power failure.  
- When you touch the temperature setting icons for the first time,  
the most recent setting ("reference setting") is displayed.  
If you touch the ALARM icon now, the highest temperature  
registered during the power failure will be displayed. Check  
the quality of the food and its suitability for consumption in  
case it has become too warm or even defrosted.  
- You can change the settings in increments of 1°C by briefly touch-  
ing the icons again. If the icons are held, the temperature setting  
will change faster.  
- Approximately 5 seconds after the last touch, the display will  
automatically show the actual freezing or cooling temperature  
("actual setting").  
The highest temperature will appear for approx. 1 minute.  
Afterthat,theactualtemperatureinthefreezerwillre-appear.  
ThedisplaycanbeswitchedoffbytouchingtheALARMicon.  
- You can change the temperatures  
in the refrigerator: between 11°C and 2°C and  
in the freezer: between -14°C and -28°C.  
SuperCool  
Touching the SuperCool icon switches the refrigerator compart-  
ment to maximum cooling. It is recommended particularly if you  
wish to cool large quantities of food, drinks, freshly baked goods  
or meals rapidly.  
Temperature display  
In normal operation, the following settings will be displayed:  
- the average refrigerator temperature and  
- the warmest frozen food temperature.  
Switching on: Touch the SuperCool icon briefly so that  
When starting up for the first time or when the  
appliance is warm, dashes will appear until  
the temperature reaches a level that can be  
displayed (below 0°C in the freezer).  
the LED  
comes on. The refrigerator temperature will  
drop to its lowest value.  
Note: The SuperCool function uses slightly more energy. After  
approximately six hours, however, the refrigerator switches back  
automatically to normal energy-saving operation. If required, the  
SuperCool function can be switched off sooner.  
The display will flash:  
- if you change the temperature or  
- if the temperature rises by several degrees, indicating cold loss,  
e.g. if you place fresh, "warm" food in the freezer or if you remove  
or re-pack frozen food the temperature may rise for a short time  
due to warm air flowing into the freezer.  
Switching off: Touch the SuperCool icon again until the LED  
goes out.  
If F1 to F5 appears in the display, the appliance has a fault. Con-  
sult the customer service department indicating the fault number  
displayed.  
15  
 
Setup mode  
= Confirm water filter change  
The following functions can be activated in setup mode:  
= Child lock  
Afterthewaterfilterhasbeenchanged,thedrop  
symbol on the display must be reset.  
Resetting the drop symbol  
= Confirm water filter change  
= Ice maker holiday mode  
• Activate setup mode by touching the  
SuperFrost icon for 5 seconds.  
= Water quantity for ice-cube tray  
= Display brightness  
• Touch the freezer compartment Down icon  
until appears in the display.  
= Door gasket heating control  
= Confirm dust filter cleaning  
• Touch the SuperFrost icon.  
- The display reads  
Activating setup mode:  
• Touch the SuperFrost icon again.  
• Touch the SuperFrost icon for 5 seconds.  
- The display reads  
- The SuperFrost LED  
- after 5 seconds will flash in the display.  
The appliance is in setup mode now.  
comes on for 5 seconds,  
• The drop symbol disappears.  
• Exit setup mode by touching  
the freezer compartment On/Off icon.  
You can select the setup mode functions by touching  
the freezer compartment temperature setting icons.  
= Ice maker holiday mode  
Note: In setup mode the display will flash continuously.  
See section entitled "Ice maker".  
Exiting setup mode:  
• Touch the freezer compartment On/Off icon  
The appliance will change back to normal operation.  
= Water quantity for ice-cube tray  
If the produced ice cubes of the ice maker are too small, the inflow-  
ing water quantity can be adjusted.  
= Child lock  
Adjusting the water quantity  
The child lock is designed to protect the appliance from being  
switched off accidentally.  
• Activate setup mode by touching the SuperFrost icon for 5 sec-  
onds.  
Activating the child lock  
• Touch the freezer compartment Down icon until  
appears in the display.  
• Activate setup mode by touching  
the SuperFrost icon for 5 seconds.  
• Touch the SuperFrost icon.  
- The display reads  
- The display reads  
• Touch the SuperFrost icon.  
• Touch the freezer compartment Up icon once only so that E 4  
- The display reads  
appears in the display.  
• Touch the SuperFrost icon again.  
Caution!  
- The  
LED is lit and the child lock is activated.  
Do not increase for more than one step. If the adjusted value  
is too high, the icecube tray of the ice maker could overflow.  
• Exit setup mode by touching  
the freezer compartment On/Off icon.  
• Touch the SuperFrost icon again.  
• Exit setup mode by touching the  
freezer compartment On/Off icon.  
Deactivating the child lock  
• Activate setup mode by touching  
Check the ice cube size within the next days. If the ice cubes are  
still too small, follow the steps above again.  
the SuperFrost icon for 5 seconds.  
- The display reads  
• Touch the SuperFrost icon.  
- The display reads  
• Touch the SuperFrost icon again.  
- The  
LED goes out. The child lock is deactivated.  
• Exit setup mode by touching  
the freezer compartment On/Off icon.  
16  
 
GB  
Interior light  
= Display brightness  
Adjusting the display brightness  
• Activate setup mode by touching the SuperFrost icon for 5 sec-  
Theinteriorlightislocatedattheleft,rightandtopintherefrigerator  
compartment and above each drawer in the freezer compartment.  
It comes on if one of the doors or a freezer drawer is opened.  
onds.  
Caution-class1Mlaserradiation. Whencoverisremoved, do  
not look directly at light through optical instruments. Severe  
eye injury can occur.  
• Touch the freezer compartment Down icon until appears in  
the display.  
• Touch the SuperFrost icon.  
The light switches off automatically if one of the doors or a freezer  
drawer has been left open for more than 15 minutes. The audible  
warning signal sounds at the same time.  
- The display reads  
• Touch the freezer compartment  
Up/Down icons to select  
If one of the strip lights is not lit, it is defective.  
0 = minimum to  
The lighting may only be replaced by the customer service  
technician or by competent skilled personnel!  
5 = maximum brightness.  
Do not try to change the defective lighting yourself!  
• Touch the SuperFrost icon at the desired value.  
• Exit setup mode by touching  
the freezer compartment On/Off icon.  
= Door gasket heating control  
Condensed water on the gasket of the refrigerator doors can be  
eliminated by activating the door gasket heating.  
Activating the door gasket heating  
• Activate setup mode by touching the SuperFrost icon for 5 sec-  
onds  
• Touch the freezer compartment Down icon until appears in  
the display.  
• Touch the SuperFrost icon.  
- The display reads  
• Touch the freezer compartment  
Up/Down icons to select  
= at slight condensation of the gasket,  
= at heavy condensation of the gasket.  
• Touch the SuperFrost icon at the desired value.  
• Exit setup mode by touching  
the freezer compartment On/Off icon.  
= Confirm dust filter cleaning  
Once the dust filter in the appliance plinth has been cleaned, the  
dust filter LED  
in the display must be cancelled.  
Cancelling the dust filter symbol  
• Activate setup mode by touching the SuperFrost icon for 5  
seconds.  
• Touch the freezer compartment Down icon until appears in  
the display.  
• Touch the SuperFrost icon.  
- The display reads  
• Touch the SuperFrost icon.  
- The display reads  
• The dust filter symbol has been cancelled.  
• Exit setup mode by touching  
the freezer compartment On/Off icon.  
17  
 
Arranging food  
Equipment  
Repositioning the door racks  
Lift door rack vertically, lift out to  
the front and re-insert at a different  
height, following these steps in the  
reverse order.  
Repositioning the shelves  
Light cover  
1. Hold the shelf underneath  
with your hand to prevent  
from tipping down back-  
wards when removing.  
2. Lift the shelf at the front.  
3. Pull the shelf towards you  
until the round cutout of  
the shelf is in line with the  
interior light cover.  
4. Lifttheshelfupandreplace  
in the desired position.  
Removing the shelves  
(1) butter, cheese  
(2) eggs  
1. Follow the first three steps  
(3) bottles  
in the chapter above.  
(4) frozen food, ice cubes  
(5) meat, sausage products, dairy products  
(6) baked goods, pre-cooked meals  
(7) fruit, vegetables  
2. Move the shelf down and  
stopjustoverthevegetable  
drawer.  
3. Move the front of the shelf  
upwards until the shelf is in  
a vertical position.  
Note  
• Food which gives off or absorbs odours and flavours as well as  
liquids should always be stored covered or in closed containers.  
• High-percentage alcohols should be tightly sealed and stored  
upright.  
4. Turn the shelf by 90° and  
remove.  
• Fruit, vegetables and salad can be stored unpacked in the draw-  
ers.  
Removing the vegetable drawer  
Pull the drawer straight out,  
grip at the back and lift out.  
Inserting the vegetable  
drawer  
Place the drawer on the pull-  
outrails.Therailsmustbefully  
extendedandalignedwiththe  
front of the drawer. Slide the  
drawer in.  
18  
 
GB  
Freezer compartment description  
Freezing with SuperFrost  
Both drawers can be used for freezing of food or storage of frozen  
Touch the SuperFrost icon briefly so that  
food.  
the  
LED comes on.  
Theice-cubebinintheupperdrawerisintendedforicecubesonly.  
• For small amounts of frozen food switch on SuperFrost 6 hours  
beforehand. For the maximum amount (see freezing capacity on  
the type plate) you will need to switch it on 24 hours beforehand.  
• Then place the fresh food inside the freezer.  
If you need the whole upper drawer for freezing or storage, the  
ice-cube bin can be removed.  
Important: The ice maker will not eject the ice cubes of its tray if  
- The SuperFrost function switches off automatically.Depending  
on the quantity of food placed in the freezer, this will normally  
be between 30 and max. 65 hours. The freezing process is now  
complete, the SuperFrost LED will go out.  
the bin has been removed.  
Ice-cube bin  
Ice maker  
You should not switch on the SuperFrost function:  
- when placing frozen food in the freezer;  
- when freezing up to approx. 2 kg fresh food daily.  
Space for freezing and  
storage  
Notes on freezing and storage  
• Always store identical food items together.  
• Packfoodwhichyouarefreezingyourselfinquantitiesappropriate  
to your household.To ensure that the food freezes right through,  
the following quantities should not be exceeded per package:  
fruit, vegetables: up to 1 kg, meat: up to 2.5 kg.  
• Pack frozen food in standard freezer bags or reuseable plastic,  
metal or aluminium containers.  
• Do not allow fresh food which is to be frozen to come into contact  
with food already frozen. Always keep packs dry in order to avoid  
them sticking together.  
• Alwayswritethedateandcontentsonthepackanddonotexceed  
the stated storage time for the food.  
• Do not freeze bottles and cans which contain carbonated drinks  
as they might burst.  
• Onlytakeoutasmuchfoodasisimmediatelyrequiredforthawing.  
Use food which has been thawed in prepared meals as quickly  
as possible.  
Freezing  
Frozen food can be thawed in the following ways:  
– in a fan oven,  
Fresh food should be frozen to the core as rapidly as possible.  
Frozen food can also be given a cold boost. This is provided by  
the SuperFrost facility.  
– in a microwave oven,  
– at room temperature,  
– in the refrigerator: the cold given off by the frozen food is used for  
cooling.  
The maximum amount of food (in  
kg) which can be frozen in 24 hours  
is shown on the type plate ("Freez-  
ing capacity"). This amount varies  
according to the model and climate  
rating.  
19  
 
Ice maker  
Safety instructions and warnings  
Ice maker holiday mode  
• Theicemakerisdesignedexclusivelytomakeicecubesinquanti-  
ties required by a household and may only be operated with water  
suitable for this purpose.  
In case of longer vacations, the ice-cube tray should be emptied.  
By setting the ice maker into the  
holiday mode, the tray will  
rotate down and no water  
remains in the tray.  
• All repairs and work on the ice maker may only be carried out by  
customer service personnel or other trained personnel.  
Therstthreebatchesoficemustnotbeconsumedorused.  
This applies both to using the appliance for the first time  
and also to using it after it has not been used for a lengthy  
period of time. This ensures that the water supply is purged.  
The freezer drawer must be  
left open so that the surface  
of the tray dries up and no mould  
or unpleasant odours can occur.  
Themanufacturercannotacceptliabilityfordamagecaused  
by a faulty connection to the mains water supply.  
• The ice maker will only work if the combined refrigerator-freezer  
is connected to the electricity supply. It will only make ice cubes  
if the freezer compartment is operating.  
• Ensure that the drawer is fully closed, as the ice maker can oth-  
Activating the ice maker holiday mode  
Be sure the upper freezer drawer is com-  
pletely closed and the ice-cube bin is  
installed correctly.  
erwise not produce ice cubes.  
Switching the ice maker on  
• Activate setup mode by touching the Su-  
perFrost icon for 5 seconds.  
Ice-cube bin  
• Touch the IceMaker icon  
so that the IceMaker LED  
comes on.  
TouchthefreezercompartmentDownicon  
until appears in the display.  
After you start the ice maker for the first time, it may take up to  
24 hours before the first ice cubes are ready.  
The production capacity depends on the temperature inside the  
freezer compartment. The lower the temperature, the more ice  
cubes can be produced over a period of time.  
Touch the SuperFrost icon.  
- The display reads  
The ice cubes fall out of the ice maker into the ice-cube bin. When  
the ice reaches a certain level in the bin, the appliance stops pro-  
ducing ice automatically.  
or  
depending on whether the ice maker is switched  
on or off.  
Switching the ice maker off  
If you do not need any ice cubes, the ice maker can be switched  
off independently of the freezer compartment.  
Touch the freezer compartment Down icon.  
- The display reads  
• Touch the IceMaker icon  
so that the IceMaker LED  
Touch the SuperFrost icon.  
goes out.  
- The digit flashes.  
The ice-cube tray rotates down.  
The ice maker can also be  
switched on and off using the  
ON/OFF button at the ice maker  
housing.  
When the interior temperature appears in the display, the tray is in  
the down position and the ice maker is switched off automatically.  
Press the button for approxi-  
mately 1 second.  
Defrosting  
Refrigerator compartment  
Therefrigeratorcompartmentdefrostsautomatically.Thewaterthat  
formsontherearwalldrainsintoareservoiratthebackoftheappli-  
ance and evaporates automatically through the compressor heat.  
Freezer compartment  
The NoFrost system automatically defrosts the appliance.  
Any moisture arising collects on the evaporator and freezes, and  
is periodically defrosted and evaporated.  
20  
 
GB  
Cleaning  
Malfunctions  
Before cleaning always switch off the appliance. Pull out the  
Yourapplianceisdesignedandmanufacturedforalengthy,reliable  
operating life with no malfunctions. If a malfunction nonetheless  
occurs during operation, check whether it is due to an operating  
error. Please note that even during the warranty period the result-  
ant servicing costs in this case will have to be borne by the owner.  
mains plug or switch off or unscrew the fuse.  
Clean the inside, equipment and outer walls with lukewarm water  
and a little detergent. Do not use abrasive or acid cleaners or  
chemical solvents.  
You may be able to rectify the following faults by checking  
Do not use steam cleaners because of the risk of injury and  
the possible causes yourself:  
damage.  
Appliance does not function:  
• Ensure that no cleaning water penetrates into the electrical com-  
ponents or ventilation grille.  
• Dry all parts well with a cloth.  
– Is the appliance switched on?  
– Is the plug correctly fitted in the mains socket?  
– Is the fuse intact?  
Loud running noise:  
• Do not damage or remove the type plate on the inside of the ap-  
– Is the appliance set up firmly on the floor?  
– Does the appliance cause nearby items of furniture or objects to  
vibrate? Please note that noises caused by the refrigerant circuit  
cannot be avoided.  
pliance. It is very important for servicing purposes.  
• Use a commercially available stainless-steel cleaning agent for  
stainless-steel appliances.  
- Inordertoachievebestpossibleprotection,applyastainless-steel  
care agent uniformly in grinding direction after cleaning. Points  
which are darker at the start and a more intensive coloration of  
the stainless-steel surface are normal.  
- Donotuseabrasivespongesorscourers,donotuseconcentrated  
cleaning agents and never use cleaning agents containing sand,  
chloride or acid or chemical solvents, as these would damage the  
surfaces and could cause corrosion.  
The temperature is not low enough:  
– Isthetemperaturesettingcorrect(see"Settingthetemperature")?  
– Have excessive amounts of fresh food been placed in the appli-  
ance?  
– Doestheseparatelyinstalledthermometershowthecorrectread-  
ing?  
– Is the ventilation system working properly?  
– Is the appliance set up too close to a heat source?  
If none of the above causes apply  
and you cannot rectify the fault  
yourself, contact the nearest cus-  
tomer service department stating  
thetypedesignation ,index and  
appliance number as indicated  
on the type plate. The type plate is  
located inside the appliance on the  
left-hand side (refrigerator).  
Cleaning the dust filter  
The dust filter in the appliance plinth must be cleaned at least  
once a year.  
1. Disconnect the appliance from the mains.  
2. Pull the bottom freezer drawer right out.  
3. Unscrew the ventilation grille.  
Shutting your appliance down  
If your appliance is to be shut down for any length of time, switch  
it off and disconnect the plug or switch off or unscrew the fuse.  
Clean the appliance and leave the door open in order to prevent  
unpleasant smells.  
The appliance complies with the relevant safety regulations and  
EC Directives 2004/108/EC and 2006/95/EC.  
All types and models are subject to continuous improvement and  
the manufacturer therefore reserves the right to make modifica-  
tions to the shape, equipment and technology.  
4. Pushdownthebuttononthefilter,tiltthefilterforwards  
and remove.  
The dust filter can be washed in a dish-  
washer or by hand using water and  
detergent.  
5. Dry the filter and then, in reverse order, replace it.  
6. Re-attach the ventilation grille.  
21  
 

La Crosse Technology Clock Radio WT 5130ER User Manual
Lathem GPS Receiver ATX GPS User Manual
Lindy Switch 32320 User Manual
Magnavox Home Theater System FW62C User Manual
Makita Power Screwdriver 6094D User Manual
Mantis Lawn Mower 811103 User Manual
MB QUART Car Stereo System RAA2400 User Manual
Melissa Fan 271005 User Manual
Mellerware Styling Iron 2 0 3 2 57 0 W User Manual
MGE UPS Systems Power Supply EX 1000 User Manual