HEARTH PRODUCTS
KITS AND ACCESSORIES
Cat. No Model
Description
750,231M
REV. NC 06/2008
h5773 ADAGIO-AG
h5774 ADAGIO-pF
Arched Face Black Facade
Arched Face Brushed Nickel Facade
TM
INSTALLATION INSTRUCTIONS FOR FACADE KITS
FOR USE wITh ADAGIO™ DIRECT-VENT GAS FIREpLACES
KIT CONTENTS:
Installer: Leave This Instruction Sheet With The Appliance.
Consumer: Retain This Instruction Sheet For Future Reference.
Facade Kit
Filigree Inset Kit
1 ea. Facade Assembly (1)
1 ea. Instruction Sheet
1 ea. Upper Filigree inset (2)
1 ea. Lower Filigree inset (3)
7 ea. Washers #10 (4)
The arched facade kits require a filigree inset kit. These kits are sold
separately. Contact your dealer for ordering information.
7 ea. Hex Head Nuts (5)
Filigree Inset Kits (Sold Separately - Required)
Cat. No.
H6845
H6846
H6847
H6848
H6849
H6850
H6851
H6852
H6853
H6854
H6855
H6856
Model
Description
Aspen, Black
1
ADAGIO-INSET-ASPEN-BK
ADAGIO-INSET-ASPEN-BN
ADAGIO-INSET-ASPEN-BKN
ADAGIO-INSET-ASPEN-G
ADAGIO-INSET-NAPA-BK
ADAGIO-INSET-NAPA-BN
ADAGIO-INSET-NAPA-BKN
ADAGIO-INSET-NAPA-G
ADAGIO-INSET-TUSCAN-BK
ADAGIO-INSET-TUSCAN-BN
ADAGIO-INSET-TUSCAN-BKN
ADAGIO-INSET-TUSCAN-G
Aspen, Brushed Nickel
Aspen, Black Nickel
Aspen, Gold
2
Napa, Black
Napa, Brushed Nickel
Napa, Black Nickel
Napa, Gold
4
7 Places
5
3
7 Places
Tuscan, Black
Tuscan, Brushed Nickel
Tuscan, Black Nickel
Tuscan, Gold
INSTALL ONLY whEN FIREpLACE IS OFF AND COOL.
Figure 1
ALL wARNINGS, pRECAUTIONS AND INSTRUCTIONS pROVIDED
IN ThE INSTALLATION INSTRUCTIONS MANUAL AND ThE CARE
ANDOpERATIONMANUALpROVIDEDwIThThEAppLIANCEAppLY
TO ThESE INSTRUCTIONS. ThOROUGhLY READ AND FOLLOw
ThE INSTRUCTIONS pROVIDED wITh ThE AppLIANCE BEFORE
pROCEEDING TO ThE FOLLOwING INSTRUCTIONS.
TOOLS / SUppLIES NEEDED:
3/8” Socket or Nutdriver
GENERAL INFORMATION
INSTALLATION INSTRUCTIONS
The arched facade kits are offered in two attractive finishes, black and
brushed nickel. If you encounter any problems or need clarification of
these instructions, contact you local distributor or dealer.
1. Install the appliance, firebox liner and logs per the Installation Instruc-
tions Manual provided with the appliance and the Installation Instruction
Sheet provided with the firebox liner kit (sold separately).
Note: The base of the appliance will need to be elevated by 3/4" minimum
above the floor to allow for the proper fit of the facade (i.e. 3/4" board as
platform). See Installation Instructions Manual.
2. Using a 3/8” socket or nutdriver, remove heat shield, screen retainer and
screen from facade. See Figure 2.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
1
|