Lennox Hearth Appliance Trim Kit TK3 33BL User Manual

LENNOX HEARTH PRODUCTS  
KITS AND ACCESSORIES  
Cat. No.  
H1538  
H1539  
H1540  
H3435  
Model  
Description  
775,175M REV. B  
12/2005  
TK3-36BL  
TK3-36PB  
TK3-36BS  
TK3-33BL  
TK3-33PB  
TK3-33BS  
3-pc. Black Trim Kit, MPE-36R,  
3-pc. Brass Trim Kit, MPE-36R  
3-pc. Stainless Trim Kit, MPE-36R  
3-pc. Black Trim Kit, MPE-33R  
3-pc. Brass Trim Kit, MPE-33R  
3-pc. Stainless Trim Kit, MPE-33R  
H3436  
H1932  
INSTALLATION INSTRUCTIONS FOR TRIM KITS  
FOR USE WITH MODELS MPE-33R AND MPE-36R ELECTRIC FIREPLACE  
* KIT CONTENTS:  
1 ea. Top Panel  
1 ea. Left Side Panel  
1 ea. Right Side Panel  
6 ea. Magnets  
* Note: Trim Kits with Brass and Stainless Finishes also include:  
~8”  
1 ea. Left Side Channel  
1 ea. Right Side Channel  
1 ea. Top Channel  
Double-sided tape on panels  
(If the kit you purchased includes channels and double-sided tape, they  
should be used)  
Figure 2  
Top Panel  
Step 2.  
*Top Channel  
Brass and Stainless Trim Kits - Proceed to Step 3.  
Black Trim Kits - Proceed to Step 4.  
Right Panel  
*Side Channels  
Step 3. Place the side channels over the magnets (See Figure 3 ).  
Ensure that the two side channels are flush with the bottom of the  
fireplace. The wider side of the side channel should be on the front of  
the fireplace face after installation.  
Left Panel  
Magnets  
Figure 1  
CAUTION: CAREFULLY SEPARATE THE MAGNETS BY TWISTING  
THEM APART. BE VERY CAREFUL WHEN HANDLING, BECAUSE  
THE MAGNETS ARE VERY POWERFUL AND CAN SNAP TO-  
GETHER UNEXPECTEDLY AND POSSIBLY PINCH THE SKIN OR  
FRACTURE THE MAGNETS.  
Side  
Channel  
Approximate  
Magnet  
Placement  
TOOLS REQUIRED:  
None  
Ensure  
Channel is  
Flush with  
Base  
INSTALLATION INSTRUCTIONS:  
This kit contains trim panels used to finish the gaps between the wall-  
board or optional mantel and the fireplace, providing the appliance a fin-  
ished built-in look.  
Figure 3  
ENSURE FIREPLACE IS COOL TO THE TOUCH BEFORE STARTING IN-  
STALLATION OF THE TRIM KIT  
Step 3. Peel off the backing on the double-sided tape on the backside  
of each side trim panel (see Figure 4 ). Avoid touching the sticky  
surface of the tape.  
Step 1. Place 2 magnets on each side of the fireplace, placed at approxi-  
mately 8” from the top and 8” from the base. See Figure 2.  
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.  
Page 1 of 2  
 

KWC Indoor Furnishings K12H311000A21 User Manual
Kyocera All in One Printer FS C1020MFP User Manual
Learning Resources Baby Toy LER 7584 User Manual
Lennox International Inc Furnace R LBF User Manual
Linear Stereo Amplifier COMP DA 1X8 User Manual
Magnavox Flat Panel Television 42MF521D User Manual
Magnavox Portable DVD Player DVD502AT User Manual
Makita Saw 3706 User Manual
Marshall electronic Microphone V69XM User Manual
Maytag Water Heater HE2930T User Manual